|
 
|
Process Control System
We offer various Process Control Systems which can be integrated for controlling the ambient environment on the premises. These are very well designed products which give a lot of control and are also easy to use and install.
|
View Enquiry Basket
 |
Auto Tune PID Temperature Controller |
 |
|
 | This new indicating controller supplied by us is designed to accept any kind of process transmitters. It is a new universal controller that handles all the common process control applications with simplicity, reliability, easy setting and low price. The following are its Technical Specifications:
• Accuracy Thermocouple ±0.3%+1 Digit or 340°C
• Except R.S.B.C Thermocouples under 450°C
• RTD, DC Volt ±0.2%+1 digit
• Input Universal Input K,J,E,N,C,T,R,S,B,JPt 100hm Pt 100 ohm,1~5Vdc -
• Control Output Relay Contact (250V 2A,R)4 ~ 20
• MA (600ohmmax.)SSr(20Vdc 21 MA) -
• Control PID, P, ON-OFF Each Heat, Cool Mode
• Process Control System Product/Service
• Control Period 1~ 60 sec. -
• Scan Time 0.16 sec. -
• Power Universal Power 100 ~ 240V ac. 50/60Hz.
• A max. -
• Operation Condition Temperature 0~50°C
• Humidity 35 ~ 85% RH No dew-condensation
• Dimension Pinele Cutout(mm) GC 48 : 48 (W) X
• 48 (H) X 90(D) : 45(w) x 45(H)- |
|
|
 |
Add to Enquiry Basket |  |
|
Digital Temperature Controller |
|
|
Our Digital Temperature controllers are designed to measure, display and control temperature of furnaces over wide range, with high accuracy. Different sensors are used for the desired temperature control range. In our temperature controller uses of proportional controller minimizes overshoot and undershoot of the furnace and completely eliminates contact problem associated with relay and contactors. The measured temperature is displayed on a digital LED display.
The Standard features of our controller are:
• Automatic cold junction compensation (Thermocouples)
• Broken sensor indication & sensor linearization
• Using DFG techniques are the standard features |
|
|
|
|
Add to Enquiry Basket | |
|
Microprocessor Based Digital Timer |
|
|
| We offer digital timer, which are fully programmable (micro-PROCESSOR based).
• Some of the features are:
• Mode of operation: ON delay / OFF delay /
• Cyclic timer
• Edge triggered timer / LEVEL Triggered timer
• Front side and rear side RESET facility provided
• Display sizes : seven segment LED display (4digit/ 6 digit )
• Single display / dual display
• Set points : 1 to 20 Nos. (In RTC based Module)
• Life long Memory Backup
• Relay output: single /dual
• Sequential timer : 1 to 36 Channels
• 48x48mm (1 rly)
• 48x96mm/72x72mm /96x96mm
• Supply voltage : 230 VAC /110V AC /24 VDC |
|
|
|
Add to Enquiry Basket | |
|
Control Card |
|
|
This three-phase ANGLE control card has servo-control and inbuilt 3ph VAF meter integrated in one unit. The significant features are:
• All functions and parameters are fully software programmable
• 3-7 segment LEDs to display
• Display of input phase voltage
• Display of input line voltage
• Display of output phase voltage
• Display of output line voltage
• Display of each phase load current
• Display of frequency
• Display of set voltage
• Overload protection
• Under/over voltage protection
• Set voltage control setting on the panel
• Provision for selecting two different modes using dip switch
• Single phase prevention/ Phase reversal protection |
|
|
|
|
Add to Enquiry Basket | |
|
|
Showcase
